__ __ |__| ____ _______/ |______ _________ ___ ____ | |/ \ / ___/\ __\__ \ \____ \ \/ // __ \ | | | \\___ \ | | / __ \| |_> > <\ ___/ |__|___| /____ > |__| (____ / __/__/\_ \\___ > \/ \/ \/|__| \/ \/ Copyright (C) Parallax System LLC. All rights reserved. https://instapxe.com/eula smartctl 7.0 2018-12-30 r4883 [x86_64-linux-3.10.0-1127.el7.x86_64] (local build) Copyright (C) 2002-18, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: TOSHIBA MK4058GSX Serial Number: 49H3P0R6T LU WWN Device Id: 5 000039 1b22806d6 Firmware Version: FF012A User Capacity: 400,088,457,216 bytes [400 GB] Sector Size: 512 bytes logical/physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 1.5 Gb/s Local Time is: Wed Oct 23 09:14:25 2024 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 120) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 176) minutes. SCT capabilities: (0x0039) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0 2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0 3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1728 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 12309 5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0 9 Power_On_Hours 0x0032 061 061 000 Old_age Always - 15979 10 Spin_Retry_Count 0x0033 253 100 030 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 5613 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 5818 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 120 193 Load_Cycle_Count 0x0032 088 088 000 Old_age Always - 125945 194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 22 (Min/Max 12/48) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 220 Disk_Shift 0x0002 100 100 000 Old_age Always - 8231 222 Loaded_Hours 0x0032 074 074 000 Old_age Always - 10423 223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0 224 Load_Friction 0x0022 100 100 000 Old_age Always - 0 226 Load-in_Time 0x0026 100 100 000 Old_age Always - 338 240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0 SMART Error Log Version: 1 ATA Error Count: 23 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 23 occurred at disk power-on lifetime: 9410 hours (392 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 32 ec 15 b5 64 Error: WP at LBA = 0x04b515ec = 78976492 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 08 48 88 14 ac 40 00 00:01:24.743 WRITE FPDMA QUEUED 61 08 40 18 0c af 40 00 00:01:24.743 WRITE FPDMA QUEUED 61 08 38 00 f6 ef 40 00 00:01:23.912 WRITE FPDMA QUEUED 60 00 30 e0 15 b5 40 00 00:01:21.037 READ FPDMA QUEUED 2f 00 01 10 00 00 40 00 00:01:21.037 READ LOG EXT Error 22 occurred at disk power-on lifetime: 9410 hours (392 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 12 ec 15 b5 64 Error: WP at LBA = 0x04b515ec = 78976492 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 08 28 f0 ff a9 40 00 00:01:18.911 WRITE FPDMA QUEUED 61 08 20 08 00 aa 40 00 00:01:18.911 WRITE FPDMA QUEUED 61 18 18 d0 e4 aa 40 00 00:01:18.910 WRITE FPDMA QUEUED 60 00 10 e0 15 b5 40 00 00:01:17.004 READ FPDMA QUEUED 2f 00 01 10 00 00 40 00 00:01:17.003 READ LOG EXT Error 21 occurred at disk power-on lifetime: 9410 hours (392 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 c2 ec 15 b5 64 Error: WP at LBA = 0x04b515ec = 78976492 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 61 01 08 10 2e 64 40 00 00:01:15.588 WRITE FPDMA QUEUED 61 30 00 78 db 38 40 00 00:01:14.742 WRITE FPDMA QUEUED 61 00 f8 78 da 38 40 00 00:01:14.742 WRITE FPDMA QUEUED 61 00 f0 78 d9 38 40 00 00:01:13.917 WRITE FPDMA QUEUED 61 00 e8 78 d8 38 40 00 00:01:13.917 WRITE FPDMA QUEUED Error 20 occurred at disk power-on lifetime: 9410 hours (392 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 ba ec 15 b5 64 Error: UNC at LBA = 0x04b515ec = 78976492 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 b8 e0 15 b5 40 00 00:01:08.914 READ FPDMA QUEUED 2f 00 01 10 00 00 40 00 00:01:08.914 READ LOG EXT 60 00 b0 e0 15 b5 40 00 00:01:04.892 READ FPDMA QUEUED 2f 00 01 10 00 00 40 00 00:01:04.891 READ LOG EXT 60 00 a8 e0 15 b5 40 00 00:01:00.869 READ FPDMA QUEUED Error 19 occurred at disk power-on lifetime: 9410 hours (392 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 41 b2 ec 15 b5 64 Error: UNC at LBA = 0x04b515ec = 78976492 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 b0 e0 15 b5 40 00 00:01:04.892 READ FPDMA QUEUED 2f 00 01 10 00 00 40 00 00:01:04.891 READ LOG EXT 60 00 a8 e0 15 b5 40 00 00:01:00.869 READ FPDMA QUEUED 2f 00 01 10 00 00 40 00 00:01:00.869 READ LOG EXT 60 00 a0 e0 15 b5 40 00 00:00:56.847 READ FPDMA QUEUED SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.